User Tools
wireless_ethernet_bridge
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| wireless_ethernet_bridge [2023/06/06 20:34] – [Steps] -formatting hogwild | wireless_ethernet_bridge [2025/11/15 19:02] (current) – [Steps] hogwild | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Wireless Ethernet Bridge Mode ====== | + | ====== |
| Wireless Ethernet Bridge Mode is an easy way to expand your network without having to run long Ethernet cable between devices. | Wireless Ethernet Bridge Mode is an easy way to expand your network without having to run long Ethernet cable between devices. | ||
| Line 6: | Line 6: | ||
| This mode is not available for all routers supporting FreshTomato. However, Media Bridge mode can serve as an alternative.(( | This mode is not available for all routers supporting FreshTomato. However, Media Bridge mode can serve as an alternative.(( | ||
| - | Support for Media Bridge mode is available starting with release 2021.6.\\ | + | Support for Media Bridge mode is available starting with release 2021.6.\\ |
| * MB mode will work with SDK7 ARM routers like the AC3200 / R8000 (Wireless Ethernet Bridge is not working/not possible). | * MB mode will work with SDK7 ARM routers like the AC3200 / R8000 (Wireless Ethernet Bridge is not working/not possible). | ||
| Line 13: | Line 13: | ||
| )) For details about these modes, see the //Wireless Mode// tables on the [[basic-network|Network]] page. | )) For details about these modes, see the //Wireless Mode// tables on the [[basic-network|Network]] page. | ||
| - | You are advised not to use Virtual Wireless interface(s) simultaneously with a physical interface in Wireless Ethernet Bridge mode. It may still work properly. However, | + | You are advised not to use Virtual Wireless interface(s) simultaneously with a physical interface in Wireless Ethernet Bridge mode. It may still work properly. However, |
| Wireless Ethernet Bridge allows only IPv4, except for SDK6 ARM dual-core routers will allow IPv6. | Wireless Ethernet Bridge allows only IPv4, except for SDK6 ARM dual-core routers will allow IPv6. | ||
| )) | )) | ||
| - | ===== Steps ===== | + | ===== Assumptions |
| - | For this HOWTO, we will: \\ | + | For this HOWTO, we will: \\ |
| - | * Refer to the network you want to expand as the "// | + | * Refer to the network you wish to expand as the "// |
| - | * Refer to the router in Wireless Ethernet Bridge mode as the "// | + | * Refer to the router in Wireless Ethernet Bridge mode as the \\ "// |
| - | * Use 192.168.1.1 as the primary router address and 192.168.1.2 as the secondary router address. | + | * Use "192.168.1.1" |
| - | * Perform all steps on the secondary router, (the one you wish to use in Wireless Ethernet Bridge mode). | + | * Perform all steps on the secondary router, (the one to use in Wireless |
| - | \\ | ||
| - | | + | ===== Steps ===== |
| - | - Go to the [[basic-network|Network]] menu//. //In the //IP Address// field in the LAN section: | + | |
| - | - Enter an IP address in the same subnet as the primary router, but outside the DHCP pool of your network. \\ We will use 192.168.1.2. | + | |
| - | - Uncheck the DHCP checkbox and click //OK//. | + | - Go to the [[basic-network|Network]] menu//. //In the //IP Address// field in the LAN section: |
| - | - Click Save. \\ \\ | + | - Enter an IP address in the same subnet as the primary router, |
| - | - Log on to the secondary router via 192.168.1.2. In the [[basic-network|Network]] menu//, //configure the settings of the interface that \\ matches | + | - Uncheck the //Use DHCP// checkbox and click //OK//. \\ \\ |
| - | - Set Wireless Mode to: Wireless Ethernet Bridge | + | |
| - | - Set Wireless Network Mode to: Auto | + | |
| - | - Set SSID to: " | + | |
| - | - Set Channel to: " | + | |
| - | - Set Channel Width to: match the primary router setting | + | |
| - | - Set Control Sideband to: match the setting on the primary router | + | |
| - | - Set Security to: match the primary router' | + | |
| - | - Set Encryption to: match the primary router' | + | |
| - | - Set Shared Key to: " | + | |
| - | - Set Group Key Renewal to: match the primary router setting (usually 3600 seconds) | + | |
| - Click Save. \\ \\ | - Click Save. \\ \\ | ||
| + | - Log on to the secondary router via 192.168.1.2. In the [[basic-network|Network]] menu//, //\\ configure the settings of the interface that matches the primary router \\ WiFi network you want to bridge (2.4GHz or 5GHz) as follows: \\ \\ | ||
| + | - Set Wireless Mode to: " | ||
| + | - Set Wireless Network Mode to: " | ||
| + | - Set SSID to: " | ||
| + | - Set Channel to: " | ||
| + | - Set Channel Width to match the primary router setting \\ \\ | ||
| + | - Set Control Sideband to match the setting on the primary router \\ \\ | ||
| + | - Set Security to match the primary router setting (usually WPA2 Personal) \\ \\ | ||
| + | - Set Encryption to match the primary router setting (usually AES) \\ \\ | ||
| + | - Set Shared Key to " | ||
| + | - Set Group Key Renewal to match the primary router setting \\ (usually 3600 seconds). \\ \\ | ||
| + | - Click Save.\\ | ||
| - In the [[basic-network|Network]] menu, in the LAN section: \\ \\ | - In the [[basic-network|Network]] menu, in the LAN section: \\ \\ | ||
| - | - Set Default Gateway to: the IP address of the primary router. We will use 192.168.1.1 | + | - Set Default Gateway to: the primary router's IP address. \\ We' |
| - | - Set Static DNS to: the primary router' | + | - Set Static DNS to: the primary router' |
| - | - In **release 2022.6** or later, selecting " | + | - In **r2022.6** or later, selecting " |
| - Click Save. | - Click Save. | ||
| \\ | \\ | ||
| - | The process is complete. You should now have a working Wireless Ethernet Bridge. | + | The process is now complete. You should now have a working Wireless Ethernet Bridge. |
| Remember to set your computer back to its previous network settings. | Remember to set your computer back to its previous network settings. | ||
wireless_ethernet_bridge.1686080071.txt.gz · Last modified: by hogwild
Page Tools
